Stem Help

A Place to idle the day away talking about anything you fancy. Expect to find cycling and non cycling topics inside

Stem Help

Postby Marek » Mon May 05, 2008 7:23 pm

Hello,

I have a ITM Luxe Lite Stem and it is not quite the right angle for my new bike. Basically I need about 1cm more rise. Could someone tell me how to work out which Stem I need and how the angles etc work as I am not an expert on this. Any advice much appreciated.

Cheers

Marek.....
Marek
lives on this board 24/7!!!
 
Posts: 1969
Joined: Sat May 03, 2003 4:21 pm

Re: Stem Help

Postby Andrew G » Mon May 05, 2008 8:02 pm

Stating the obvious here and you've probably already tried it, but can you just flip it? If it is currently giving a neutral rise then flipping it round will give a slight rise. Depends from stem to stem but might work for you.
Andrew G
lives on this board 24/7!!!
 
Posts: 10477
Joined: Tue Oct 04, 2005 6:47 pm
Location: Selsdon

Re: Stem Help

Postby Jon H » Mon May 05, 2008 8:12 pm

Only need 1cm?
I get lots of spam emails promising much more rise of the stem than that.
User avatar
Jon H
lives on this board 24/7!!!
 
Posts: 3392
Joined: Wed Nov 27, 2002 1:30 pm
Location: Bromley

Re: Stem Help

Postby Marek » Mon May 05, 2008 8:13 pm

Right, the ITM Luxe Lite has an 80' angle, whatever that means, but when I flip it the rise is too much, I kind of need something in between. But only problem is that I don't know whether I need something with a larger or smaller angle as not sure where the 80' is measured.
Marek
lives on this board 24/7!!!
 
Posts: 1969
Joined: Sat May 03, 2003 4:21 pm

Re: Stem Help

Postby Marek » Mon May 05, 2008 8:14 pm

Jon, I have no doubt that you get a lot of those types of emails from all the websites that you have subscribed to. Any suggestions on the Stem would be great.
Marek
lives on this board 24/7!!!
 
Posts: 1969
Joined: Sat May 03, 2003 4:21 pm

Re: Stem Help

Postby Sylv » Mon May 05, 2008 8:38 pm

Hmm, using distant memories of math classes, assuming you have a long-ish stem of say 130mm, with the 10 degree angle (or 80 degree depending on what the manufacturer calls it), the effective rise at the end of the stem should be 23mm.

So if you reversed the stem you would have -23mm or a 46mm difference, way too much as you noticed.

If you can't fit a 10mm spacer, you would need a stem with a 14 or 15 degree angle (ie 76 or 75) to get 10mm more rise.

I think it's right but don't mind being corrected ...
User avatar
Sylv
lives on this board 24/7!!!
 
Posts: 5742
Joined: Wed Mar 21, 2007 2:40 pm
Location: londinium, lugdunum

Re: Stem Help

Postby Jon H » Mon May 05, 2008 8:44 pm

Oh, you mean that sort of stem :oops:

Have you got any spacers under the stem at the moment? If you just flip the stem over it will raise the bars up quite a lot, but you might be able to get to the right height by removing the spacers. Otherwise, you'll need to look for a stem with a slightly different angle. I'm guessing you're using something like a 13cm stem given your height, so a bit of trigonometry suggests you need about another 4 degrees to raise it by 1cm, so look for a stem with a 84 degree angle or thereabouts.
User avatar
Jon H
lives on this board 24/7!!!
 
Posts: 3392
Joined: Wed Nov 27, 2002 1:30 pm
Location: Bromley

Re: Stem Help

Postby Sylv » Mon May 05, 2008 8:45 pm

Alternatively, get one of these :lol:

[img]http://www.lickbike.com/lickimages/1186.gif[/img]
User avatar
Sylv
lives on this board 24/7!!!
 
Posts: 5742
Joined: Wed Mar 21, 2007 2:40 pm
Location: londinium, lugdunum

Re: Stem Help

Postby Sylv » Mon May 05, 2008 8:51 pm

Jon's right, you need 80 + 4 and not 80 - 4. So still a negative rise but 4 degrees less steep.
Last edited by Sylv on Mon May 05, 2008 8:52 pm, edited 1 time in total.
User avatar
Sylv
lives on this board 24/7!!!
 
Posts: 5742
Joined: Wed Mar 21, 2007 2:40 pm
Location: londinium, lugdunum

Re: Stem Help

Postby Wal » Mon May 05, 2008 8:51 pm

[quote]If you can't fit a 10mm spacer, you would need a stem with a 14 or 15 degree angle (ie 76 or 75) to get 10mm more rise.


Nope, a 74 or 75 stem would be either much lower or much higher than the 80/10 deg stem, depending on which way up you mounted it.

An 84/96 degree stem should see you right.
User avatar
Wal
lives on this board 24/7!!!
 
Posts: 281
Joined: Wed Jul 12, 2006 10:36 am
Location: Croydon

Re: Stem Help

Postby Marek » Mon May 05, 2008 9:25 pm

Cheers guys, have had a look around on the shopping sites but half of them don't say what angles the stems are which aint much use. For the short term I may go for flipping the stem moving it down a bit and sticking the spacers on top, a bit of a bodge but better that than a sore back hey. Thanks for the angle and tips.

Cheers

Marek.....
Marek
lives on this board 24/7!!!
 
Posts: 1969
Joined: Sat May 03, 2003 4:21 pm


Return to General

Who is online

Users browsing this forum: No registered users and 54 guests

cron